Bourse Class

Hi everyone! It’s time for our bourse class weekend πŸ™‚

All the pictures are clickable and shall lead you to a larger view.
You can see the list of materials needed here. The most important thing is having:

  • a square design, with plenty of margin around
  • an outer fabric of the same size (you can take any kind you want – cotton, silk, satin, brocade, whatever)
  • some ribbon or cording to gather and tie the bourse (I chose narrow lace).

Bourse material list

1. I’m going to start with a little tip I came up with to make sure you sew a perfectly, perfectly straight line all around the design. The tip was inspired to me by a technique in garment sewing (namely, pulling a thread near the edge of a fabric to determine the grain). We are going to pull a thread from the linen on each side of the stitched piece, right where the seam shall be.
For the first side, you’ll just have to determine the seam allowance. It’s your call – I like 1cm (3/8″) for those small projects πŸ™‚ Once you have decided this, pick up the thread in the linen right on the line where you want the seam to be. I pick it up with a seam ripper, but small pointed scissor will work, too. Do be careful to pick up just this thread. Cut it and pull it out of the linen. You will end up with a small groove, which shall be your seamline πŸ™‚

01countingsewingline.jpg

For the other sides, you’ll first have to go back to the first side and to count the number of linen threads between the stitched design and the thread you just pulled out. Then, count the same number of threads on each side, and pull a linen thread on each side.
You will end up with this:

02line.jpg
(Oops! The linen started fraying – but not enough to get me worried. Just handle it carefully – we’ll be trimming it in no time anyway πŸ˜‰ )

Now we can really start sewing πŸ™‚

2. Assemble the outer fabric and the stitched piece.
Pin them right sides together, with the stitched piece on top (since the groove we created in the linen will serve as a guideline)

03pinned-right-sides-together.jpg

Start sewing, starting not quite in the middle of a side. Whether you will be sewing by hand or by machine, all you have to do is sew right in the groove created by the pulled threads. Easy, non? πŸ™‚

 

04sewing-in-the-line.jpg

Go around the whole square, and stop 2-3 inches before the beginning of the seam. This will be the opening through which you’ll turn the bourse inside out. (Do not start sewing in a corner. It will be much more of a pain to slipstitch a corner than a straight line, when you close the opening!)

3. Trim the seams close to the seamline (I do it with pinking shears so that the fabric and linen won’t fray) and clip the corners. This will ensure crisp edges and corners when you turn the work inside out.

 

05sewn-pinked.jpg

4. Turn your work inside out. Press it carefully (press, do not iron. Pressing ensures you do not distort the seamline and fabric).
Slipstitch the opening closed. (Slipstitching is explained and illustrated in the middle of this page.)

 

07-opening-slipstitched.jpg

5. Creating the casings:
Fold the corners to the outside fabric to form isosceles triangles

08-corners.jpg 09-corners.jpg

 

10pinned-corners.jpg

Sew the corners down, stitching a line parallel to the folded edge. This creates the casing. Make sure your casing is wide enough to accommodate two widths of your ribbon/cording/narrow lace.

11corners-sewn1.jpg

The stitching line is barely visible, which is a good thing πŸ™‚

 

11corners-sewn2.jpg

6. Insert ribbon into the casings. (I use a large knitter’s sewing needle, but anything goes).
Once the first length of ribbon/cording is threaded through the casings, make a knot to close it. To determine the length, just make sure it lies flat around the (still open) bourse.

12first-ribbon-threaded.jpg

Starting from the other side, thread the second length of ribbon/cording through the casings.

13both-ribbons-threaded-and-knotted.jpg

All you need to do now is to pull the ribbons in order to gather up the edges and close the bourse.

17.jpg 14-bbourse-closed.jpg

Optional: You may sew a button to each corner of the bourse, if desired.

16button1.jpg

In my case I only sewed one button on to show you, but removed it afterwards. This particular bourse is small, and I felt the buttons would overload it.

Et voilΓ  !
Now you have a cute little bourse, to give or to keep πŸ™‚

I hope this was clear. If not, please feel free to ask any question by posting in the comments. Again, there is never anything such as a dumb question. Ask me how I know – I’m a teacher! πŸ˜‰

Also, if you make a bourse, please post a picture to the blog for everyone to enjoy πŸ™‚

Have fun everyone! Happy bourse-ing πŸ˜‰

Advertisements

Bourse class – materials list

Hi everyone!

We shall be having a bourse class weekend on May 19-20.

07-02-07karen-bourse.jpg

Here’s a list of what you’ll need to make a bourse:

Materials:

  • stitched piece: you need a square design to make a bourse, and you’ll (obviously) need to cut the linen into a square, leaving a generous margin around the design. My design was 9.2 cm square (3″ 3/4) and I added a 5-cm (2″) margin, PLUS a seam allowance. For a larger design, you will probably want a larger margin. To determine the width of your margin, just keep this in mind: the stitched piece shall form the bottom of the bourse, and the margins form the sides of the bourse. Do not forget to add seam allowances! (I use 1-cm allowances for small projects)
  • fabric square of the same size – I tend to cut mine slightly larger: better be safe than sorry, right? πŸ˜‰
  • ribbon, narrow lace or cording (length will depend on your bourses’s size)
  • (optional) four buttons
  • sewing thread that matches the linen

Tools:

  • ruler or measurer’s tape
  • scissors
  • (optional) pinking shears
  • pins
  • seam ripper or small pointed scissors
  • chopstick or whatnot to turn your work inside out and make crisp corners
  • hand-sewing needle

Bourse material list

(only the essentials are featured in the picture)

This is a very easy project, and while a sewing machine will make your work go quicker, you can absolutely do this by hand. Your work will even be more accurate if you sew it by hand – and it won’t take that long, I promise. πŸ™‚

Anyone can do this project – it is ridiculously easy!

Please feel free to ask if you have any question. We all know there is no such thing as a dumb question πŸ˜‰

IsabelleΒ